How To Replace Samsung Washer Bearings: A Step-By-Step Guide To Fix Your Washer Noise

Samsung washing machines are known for their reliability and durability. However, like any mechanical device, they can experience wear and tear over time. One common issue that can arise is the failure of the washer bearings. If you hear a loud grinding or humming noise coming from your Samsung washer, it’s likely that the bearings need to be replaced.

Replacing Samsung washer bearings can be a daunting task, but it’s not impossible to do yourself. With the right tools and a little patience, you can save yourself the cost of hiring a professional. In this guide, we’ll walk you through the step-by-step process of how to replace Samsung washer bearings.

Tools and Materials You’ll Need

Before you begin, gather the following tools and materials:

• New Samsung washer bearing kit
• Screwdriver (Phillips head and flathead)
• Socket wrench
• Torque wrench
• Hammer
• Punch
• Pry bar
• Lubricating grease
• Safety glasses

Safety Precautions

Before you start working on your washer, be sure to take the following safety precautions:

• Unplug the washer from the power outlet.
• Turn off the water supply to the washer.
• Wear safety glasses to protect your eyes from flying debris.

Step-by-Step Instructions

1. Remove the Top Panel

• Start by removing the top panel of the washer. There are usually two or three screws located on the back of the panel.
• Once the screws are removed, lift the panel up and off the washer.

2. Remove the Back Panel

• Next, remove the back panel of the washer. There are typically four or five screws located around the perimeter of the panel.
• Once the screws are removed, lift the panel up and off the washer.

3. Remove the Drive Belt

• Locate the drive belt and remove it from the pulley. The drive belt is usually located on the right side of the washer.
• To remove the belt, simply pull it off the pulley.

4. Remove the Motor

• Next, remove the motor from the washer. There are usually four bolts that hold the motor in place.
• Once the bolts are removed, lift the motor up and out of the washer.

5. Remove the Pulley

• Locate the pulley and remove it from the shaft. The pulley is usually held in place by a nut.
• To remove the pulley, simply loosen the nut and pull the pulley off the shaft.

6. Remove the Old Bearings

• Now, you can remove the old bearings from the shaft. The bearings are usually held in place by a snap ring.
• To remove the snap ring, simply use a punch to pry it off.
• Once the snap ring is removed, the bearings can be pulled off the shaft.

7. Install the New Bearings

• Apply a thin layer of lubricating grease to the new bearings.
• Slide the new bearings onto the shaft.
• Install a new snap ring to hold the bearings in place.

8. Install the Pulley

• Place the pulley back onto the shaft.
• Tighten the nut to secure the pulley.

9. Install the Motor

• Lift the motor back into the washer.
• Install the four bolts to secure the motor.

10. Install the Drive Belt

• Place the drive belt back onto the pulley.
• Pull the belt tight to ensure that it is properly tensioned.

11. Install the Back Panel

• Place the back panel back onto the washer.
• Install the four or five screws to secure the panel.

12. Install the Top Panel

• Place the top panel back onto the washer.
• Install the two or three screws to secure the panel.

13. Reconnect the Water Supply and Power

• Reconnect the water supply to the washer.
• Plug the washer back into the power outlet.

Testing the Washer

Once you have replaced the bearings, it’s important to test the washer to make sure that it is working properly.

• Turn on the water supply to the washer.
• Select a wash cycle and start the washer.
• Listen for any unusual noises. If you hear any grinding or humming noises, the bearings may not have been installed correctly.
• Check for leaks. If you see any water leaking from the washer, the bearings may not have been installed properly.

If you are satisfied with the performance of the washer, you can now use it as normal.

Recommendations

Replacing Samsung washer bearings can be a challenging task, but it is possible to do yourself with the right tools and a little patience. By following the steps outlined in this guide, you can save yourself the cost of hiring a professional.

Common Questions and Answers

1. How often should I replace my Samsung washer bearings?

The lifespan of Samsung washer bearings can vary depending on the frequency of use and the environment in which the washer is used. However, it is generally recommended to replace the bearings every 5-7 years.

2. What are the signs of worn Samsung washer bearings?

The most common sign of worn Samsung washer bearings is a loud grinding or humming noise coming from the washer. Other signs include:

• Leaking water from the washer
• Difficulty spinning the washer drum
• Vibration during the wash cycle

3. Can I replace Samsung washer bearings myself?

Yes, it is possible to replace Samsung washer bearings yourself with the right tools and a little patience. However, if you are not comfortable working on appliances, it is best to hire a professional.