Step-By-Step Tutorial: How To Replace A Maytag Washer Gear Case In Minutes
What To Know
- Replacing a Maytag washer gear case can be a daunting task, but with the right tools and instructions, you can get the job done right.
- Unplug the washer from the electrical outlet and turn off the water supply at the valves behind the washer.
- Use a socket wrench to remove the bolts securing the gear case to the washer tub.
Replacing a Maytag washer gear case can be a daunting task, but with the right tools and instructions, you can get the job done right. This comprehensive guide will walk you through every step of the process, from gathering the necessary materials to testing the new gear case.
Tools and Materials You’ll Need
- New Maytag washer gear case
- 5/16-inch socket wrench
- 7/16-inch socket wrench
- 1/2-inch socket wrench
- Adjustable wrench
- Screwdriver
- Pliers
- Bucket
- Towels
Step-by-Step Instructions
1. Unplug the Washer and Turn Off the Water Supply
Safety first! Unplug the washer from the electrical outlet and turn off the water supply at the valves behind the washer.
2. Remove the Front Panel
Use a screwdriver to remove the screws holding the front panel in place. Carefully lift the panel off and set it aside.
3. Disconnect the Wires and Hoses
Disconnect the electrical wires and hoses connected to the gear case. Use pliers to loosen the hose clamps and gently pull the hoses off.
4. Remove the Gear Case Bolts
Use a socket wrench to remove the bolts securing the gear case to the washer tub. There will typically be four or six bolts.
5. Lift Out the Old Gear Case
Carefully lift the old gear case out of the washer tub. Be sure to support the weight of the case with one hand while unbolting it with the other.
6. Inspect the Gear Case
Inspect the old gear case for any damage or wear. If there are any cracks, breaks, or excessive wear, it’s important to replace the gear case.
7. Install the New Gear Case
Place the new gear case into the washer tub and align it with the bolt holes. Use a socket wrench to tighten the bolts securely.
8. Reconnect the Wires and Hoses
Reconnect the electrical wires and hoses to the gear case. Tighten the hose clamps securely using pliers.
9. Replace the Front Panel
Lift the front panel back into place and secure it with the screws.
10. Turn On the Water Supply and Plug in the Washer
Turn on the water supply at the valves behind the washer. Plug the washer back into the electrical outlet.
11. Test the New Gear Case
Run the washer through a full cycle to test the new gear case. Listen for any unusual noises or vibrations. If everything sounds and looks normal, your gear case replacement is complete!
Troubleshooting Tips
- If the washer won’t spin or agitate, check the gear case bolts to make sure they are tight.
- If there is a leak coming from the gear case, check the hoses and hose clamps for damage or loose connections.
- If the washer makes a loud noise during operation, the gear case may be damaged and need to be replaced.
Wrapping Up
Replacing a Maytag washer gear case can be a challenging task, but it’s definitely doable with the right tools and instructions. By following these steps carefully, you can save yourself the cost of calling a repair technician and get your washer back up and running in no time.
Frequently Asked Questions
Q: How long will it take to replace the gear case?
A: The replacement time can vary depending on your skill level and the type of washer you have. Typically, it takes around 2-4 hours.
Q: What are the signs that my gear case needs to be replaced?
A: Common signs include leaking water, excessive noise during operation, and the washer not spinning or agitating properly.
Q: Can I use a used gear case?
A: It’s not recommended to use a used gear case as it may have hidden damage that could shorten its lifespan.