Drain Your Amana Washer In Minutes For A Stress-Free Move: The Easy Way

Moving can be a stressful task, and draining your Amana washer before moving can add to the hassle. However, with the right steps and a little preparation, you can drain your washer efficiently and prepare it for relocation. This comprehensive guide will provide you with step-by-step instructions and essential tips to ensure a smooth draining process.

Materials You’ll Need

• Towels or rags
• Bucket or large container
• Drain hose (if not attached to the washer)
• Adjustable wrench or pliers
• Screwdriver (optional)

Step-by-Step Instructions

1. Unplug the Washer and Shut Off Water Supply

• Disconnect the washer from the power outlet.
• Locate the water supply valves behind the washer and turn them off.

2. Disconnect the Drain Hose

• If the drain hose is not permanently attached to the washer, locate it behind the washer and detach it from the drainpipe.
• Place the end of the drain hose into a bucket or large container to collect the water.

3. Remove the Access Panel

• Most Amana washers have an access panel located on the front or back of the machine.
• Use a screwdriver to remove the screws holding the panel in place.

4. Locate the Drain Pump Filter

• Once the access panel is removed, you will see the drain pump filter.
• It is usually a small, round or oval-shaped component with a cap or lid.

5. Remove the Drain Pump Filter

• Carefully unscrew or remove the cap or lid of the drain pump filter.
• Be prepared for some water to leak out.

6. Clean the Drain Pump Filter

• Remove any debris or lint from the filter and the filter housing.
• Use a toothbrush or soft cloth to clean the filter thoroughly.

7. Reinstall the Drain Pump Filter

• Once the filter is clean, replace it back into the drain pump housing.
• Tighten the cap or lid securely.

8. Check the Drain Hose for Clogs

• Inspect the drain hose for any kinks or clogs.
• If necessary, use a wire hanger or plumber’s snake to clear any obstructions.

9. Reconnect the Drain Hose

• If you detached the drain hose, reconnect it to the drainpipe.
• Make sure it is securely fastened.

10. Test the Washer

• Turn on the water supply valves.
• Run a short wash cycle without any clothes to ensure the washer is draining properly.

11. Dry the Washer

• Use towels or rags to dry the inside and outside of the washer.
• Leave the access panel open to allow the washer to air dry completely.

12. Prepare for Moving

• Once the washer is completely dry, secure the drain hose and access panel.
• Disconnect the water supply hoses and drain hose.
• Tape or secure any loose parts to prevent damage during transport.

Tips for a Smooth Draining Process

• Wear old clothes or towels as you may get wet during the process.
• Place towels or rags around the washer to absorb any spills.
• Use a flashlight to illuminate the inside of the washer when removing the drain pump filter.
• If you encounter any difficulties, do not hesitate to consult the washer’s user manual or contact a qualified appliance technician.

Next Steps After Draining

• Pack the washer securely in a moving box or wrap it with blankets to protect it during transport.
• Transport the washer upright to avoid damage to the suspension system.
• Once the washer is moved to its new location, reconnect the hoses, drain hose, and power cord.

Troubleshooting Common Issues

• Washer is not draining completely: Check the drain hose for kinks or clogs. Clean the drain pump filter and housing.
• Water is leaking from the drain hose: Tighten the connection between the drain hose and the drainpipe. Replace the drain hose if it is damaged.
• Washer is not spinning: Ensure the lid or door is properly closed. Check the drain pump filter for debris.

Wrapping Up: A Smooth Moving Experience

By following these steps and tips, you can efficiently drain your Amana washer for moving and prepare it for transport. Remember to take precautions to prevent damage and ensure a smooth relocation process. With proper care and attention, your washer will be ready to operate in its new home without any hiccups.

Frequently Asked Questions

1. Can I drain my Amana washer without removing the access panel?

No, it is not recommended to drain the washer without removing the access panel. Removing the panel allows you to access the drain pump filter, which is essential for cleaning and removing any debris that may be blocking the drain.

2. What should I do if I cannot remove the drain pump filter?

If you encounter difficulty removing the drain pump filter, do not force it. Consult the washer’s user manual or contact a qualified appliance technician for assistance.

3. Can I use a vacuum cleaner to clean the drain pump filter?

Using a vacuum cleaner to clean the drain pump filter is not recommended. The suction force of the vacuum cleaner can damage the filter or the washer’s internal components.